Windows Failed to Start. A Recent Hardware or Software Change May Be the Cause Windows 2008r2

If you are facing this error, so chances are yous may take installed new hardware or software which is causing the event. Sometimes installing the latest Windows updates seems to cause this issue merely you can't exist sure until you troubleshoot the event. Now every bit far as software problems are concerned, these might be the possible reasons as to
why yous are facing this mistake:

• Corrupted BCD information
• System File is damaged.
• Loose or faulty SATA/IDE Cable
• Conflicting third party software
• Virus or malware

The mistake which you will get after a reboot will be:

Error: Windows failed to start. A recent hardware or software change might accept caused the issue after y'all install Windows Updates

The principal trouble is that you lot won't kick into Windows and yous will be stuck at this error bulletin screen. In brusk, yous will be inside a reboot loop every bit every time you restart your PC you will once more face the same error message until you lot fix the issue. So without wasting whatsoever time let's run across how actually to Fix "Windows failed to kickoff. A contempo hardware or software alter might be the cause" with the below-listed troubleshooting steps.

Fix Windows failed to commencement. A recent hardware or software change might be the cause.

Method 1: Run Startup/Automatic Repair

1. Insert the Windows ten bootable installation DVD or Recovery Disc and restart your PC.

2. When prompted to Press any key to boot from CD or DVD, press any key to go along.

3. Select your language preferences, and click Next. Click Repair your computer in the bottom-left.

iv. On choose an selection screen, click Troubleshoot.

v. On Troubleshoot screen, click the Advanced pick.

vi. On the Advanced options screen, click Automated Repair or Startup Repair.

7. Wait till the Windows Automatic/Startup Repairs complete.

eight. Restart and yous have successfully Set Windows failed to commencement. A recent hardware or software change might be the cause , if not, continue.

Also Read: How to prepare Automatic Repair couldn't repair your PC.

Method ii: Boot into Last Known Good Configuration

Before going whatsoever further let's talk over how to Enable Legacy Advanced Boot Menu so that yous can hands get Boot Options:

one.  Restart your Windows 10.

2. As the system restarts enter into BIOS setup and configure your PC to boot from CD/DVD.

three. Insert the Windows x bootable installation DVD and restart your PC.

iv. When prompted to Press any key to boot from CD or DVD, press any fundamental to go on.

5. Select your language preferences,and click Next. Click Repair your computer in the bottom-left.

6. On choose an option screen, click Troubleshoot.

vii. On Troubleshoot screen, click the Advanced option.

8. On Avant-garde options screen, click Control Prompt.

9. When the Control Prompt(CMD) open up type C: and striking enter.

10. Now type the following command:

          BCDEDIT /SET {DEFAULT} BOOTMENUPOLICY LEGACY                  

11. And hitting enter to Enable Legacy Advanced Kick Menu.

12. Close Command Prompt and dorsum on the Cull an option screen, click Continue to restart Windows x.

13. Finally, don't forget to eject your Windows 10 installation DVD to get Boot options.

fourteen. On the Boot Options screen, choose  "Concluding Known Good Configuration (Advanced)."

Method 3: Perform a System Restore

i. Put in the Windows installation media or Recovery Drive/Organisation Repair Disc and select your language preferences, and click Next

2. Click Repair your figurer at the lesser.

3. Now, choose Troubleshoot and and so Advanced Options.

4. Finally, click on "Organisation Restore" and follow on-screen instructions to complete the restore.

5. Restart your PC to save changes and see if you can fix Windows failed to outset. A contempo hardware or software change might be the cause mistake.

Method 4: Run SFC and CHKDSK

one. Once again go to control prompt using the method 1, click on command prompt in the Advanced options screen.

2. Blazon the following command in cmd and striking enter later on each 1:

sfc /scannow /offbootdir=c:\ /offwindir=c:\windows chkdsk C: /f /r /x

Note: Make sure you use the drive letter where Windows is currently installed. Also in the above command C: is the drive on which nosotros want to check deejay, /f stands for a flag which chkdsk the permission to prepare whatsoever errors associated with the drive, /r let chkdsk search for bad sectors and perform recovery and /x instructs the check disk to dismount the drive earlier start the process.

3. Get out the command prompt and restart your PC.

Method 5: Rebuild BCD configuration

one. Using above method open command prompt using Windows installation disk.

2. Now type the following commands 1 by i and hit enter afterward each one:

bootrec.exe /FixMbr bootrec.exe /FixBoot bootrec.exe /RebuildBcd

three. If the higher up command fails, and then enter the following commands in cmd:

bcdedit /export C:\BCD_Backup c: cd boot attrib bcd -southward -h -r ren c:\boot\bcd bcd.old bootrec /RebuildBcd

iv. Finally, exit the cmd and restart your Windows.

five. This method seems to Fix Windows failed to start. A contempo hardware or software change might cause the error, simply if it doesn't work for y'all, so keep.

Method half dozen: Gear up Correct Boot Guild

1. When your reckoner starts (Earlier the boot screen or the error screen), repeatedly printing Delete or F1 or F2 key (Depending upon your computer'due south manufacturer) to enter BIOS setup.

two. Once you are in BIOS setup, select the Kick tab from the list of options.

three. Now make certain that the figurer Hard disk or SSD is set equally a top priority in the Kick guild. If not, use up or downward pointer keys to set hard disk at the meridian, which means the estimator will beginning boot from information technology rather than any other source.

four. Finally, press F10 to salvage this change and exit.

Recommended:

• Gear up Loftier CPU Usage Past TiWorker.exe
• 10 means to prepare A deejay read mistake occurred
• Fix Loftier CPU Usage by svchost.exe (netsvcs)
• Gear up High CPU Usage by RuntimeBroker.exe

That'due south it you take successfully Gear up Windows failed to start. A contempo hardware or software change might exist the cause, just if y'all still have any questions regarding this post, please inquire them in the comment'due south section.